top of page
Search

Mitsubishi Carbide Malaysia: How to Match Coatings to Your Workpiece Material

13 minutes ago
3 min read

Walk into any tool crib and you will find end mills that look similar but wear very differently, and the main reason is often the coating. For shops buying Mitsubishi Carbide in Malaysia, the coating names (IMPACT MIRACLE, MS Plus, VQ and others) can seem like marketing. They are in fact a practical shorthand for which material a tool was designed to cut. This guide explains what the coatings do and how to match them to your work, based on Mitsubishi Materials' own technical information.

What a coating actually does

A coating is a thin ceramic layer on the carbide substrate. It adds hardness, resists the heat at the cutting edge and reduces friction and adhesion between chip and tool. Different workpiece materials stress the tool in different ways: hardened steel brings heat and chipping, stainless steel brings work hardening and built-up edge, aluminium brings sticking, and copper brings adhesion. No single coating is best at all of these, which is why Mitsubishi Materials offers several.

Coating guide by workpiece material

The list summarises what Mitsubishi Materials states for each coating. Figures are the manufacturer's published values and comparisons, so confirm them in the current catalogue before quoting them to customers.

  • IMPACT MIRACLE (hardened steel, heat-resistant alloys): a single-phase nano crystal (Al,Ti,Si)N coating, stated to give faster cutting speeds and longer tool life in high-hardness materials and heat-resistant alloys.

  • MS Plus (pre-hardened and hardened steels): an (Al,Ti,Cr)N multilayer coating, stated to give long tool life on materials up to 52 HRC.

  • VQ (stainless steel and other difficult-to-cut materials): an (Al,Cr)N coating with a smoothing treatment for lower cutting resistance and better chip discharge.

  • CRN (copper electrodes and copper alloys): chosen for wear resistance, adhesion strength and low friction at high temperature.

  • DLC (aluminium alloys): a diamond-like coating for high-speed milling of aluminium.

  • CVD and plasma-CVD diamond (graphite, non-ferrous and hard brittle materials): chosen for abrasion resistance and smoothness.

How the numbers compare

For IMPACT MIRACLE, Mitsubishi Materials lists a coating hardness of 3700 HV against 3200 HV for (Al,Ti,Si)N and 2800 HV for (Al,Ti)N, an oxidation temperature of 1300°C against 1100°C and 840°C, and a friction coefficient of 0.48 against 0.53 and 0.58. MS Plus is listed at 3200 HV and 1100°C. Higher oxidation temperature means the coating survives hotter cutting zones, and lower friction helps prevent chipping in hardened steel. These are laboratory-style coating properties, not a guarantee of tool life on your machine.

Substrate and geometry still matter

A good coating on the wrong geometry will still fail. Check three things alongside the coating:

  1. Flute count and helix. Fewer flutes give more chip space for aluminium and roughing, while more flutes give stability for finishing and harder materials.

  2. Corner radius or ball nose. A radius spreads load and protects the edge.

  3. Neck and reach. Longer reach reduces rigidity, so reduce depth and feed accordingly.

For mould and die work, MOLDINO tools are designed for hardened steel and finishing, so the choice between Mitsubishi Materials and MOLDINO often comes down to application. For general machining of steel, stainless and aluminium, the Mitsubishi Carbide range is typically where to look first.

A quick selection routine

  1. Write down the material and its hardness (or grade).

  2. Pick the coating family from the list above.

  3. Choose geometry for the operation: roughing, semi-finishing or finishing.

  4. Start from the manufacturer's recommended cutting conditions.

  5. Run a trial, measure tool life and adjust one parameter at a time.

Practical takeaways for Malaysian machine shops

  • Coating names map to materials. Match them to your actual workpiece rather than choosing one all-rounder for everything.

  • Do not use an aluminium-oriented tool on steel, or the reverse. Mixed use shortens the life of both.

  • Treat published hardness and temperature numbers as comparisons between coatings, not as promises for your job.

  • Label tools in the crib by material family so operators grab the right one under time pressure.

Talk to an authorised distributor

KS Precision Tools (M) Sdn Bhd is an authorised distributor in Malaysia for DIAEDGE and Mitsubishi Materials, MOLDINO, ROHM, OKABE and H.T.D Hayasaka. If you are unsure which coating suits your material, send us the grade, operation and machine, and our team in Seri Kembangan will suggest a starting point.

Sources

 
 
 

Recent Posts

See All

Comments


Copy of KS Logo (TikTok).png

KS PRECISION TOOLS

GROUP OF COMPANIES

Copyrights by KS PRECISION TOOLS (M) SDN BHD – 2024.
Created by Project One Soltion. All Rights Reserved. Privacy Policy

bottom of page