
Cost-Per-Part Beats Price-Per-Tool: Mitsubishi Materials Tooling for Malaysian Shops Facing Rising Costs
Malaysian factories are busier, but margins are under pressure. S&P Global's October 2026 survey put Malaysia's manufacturing PMI at 51.0, up from 49.9 in September and the strongest reading since April. For machine shops, that is good news on orders and a warning on costs. This post explains why cost-per-part is the number to watch, and how choosing Mitsubishi Materials cutting tools in Malaysia can be a margin decision rather than a purchasing one.
What the October PMI tells machine shops
The survey reported that new orders returned to growth, partly on demand for AI-related products, and that the pace was among the fastest in about four and a half years. Manufacturers also hired for a third consecutive month. Output, however, rose only marginally.
The cost side was less comfortable. Higher transport and raw material costs, partly linked to the Middle East conflict, lifted operating expenses, and firms responded by raising selling prices. Supplier delivery delays continued for an eleventh straight month, with port congestion a factor, and business confidence slipped to its lowest level since April.
For a CNC shop, the message is clear: you may have more work than last quarter, but material, freight and lead times are all moving against you. Anything you can control inside your own four walls matters more.
Why tool price is the wrong number
Cutting tools are usually a small share of the cost of a machined part. Machine time, labour, scrap, rework and set-up typically outweigh the price of the insert or end mill. A cheaper tool that wears out sooner or forces slower parameters can raise your cost-per-part even though the purchase price looks lower.
A simple cost-per-part formula
For each job, add up the tool cost per part, the machine time per part multiplied by your machine hourly rate, the labour for tool changes and offsets, and the cost of any scrap or rework. Divide by good parts produced.
To see how it works, take a hypothetical example (illustrative numbers only, not data from any customer). Tool A costs less but needs changing twice as often and cuts at lower feed. Tool B costs more per piece, lasts longer and allows a higher feed rate. Once you count machine minutes and stoppages, Tool B can come out cheaper per part, even though the invoice price is higher. The only way to know for your job is to measure it.
Where Mitsubishi Materials tooling can help
Mitsubishi Materials publishes detailed technical information on its coatings and geometries, which makes it easier to select a tool for a specific material rather than guessing. For example, the company describes its IMPACT MIRACLE coating as aimed at faster cutting speeds and longer tool life in high-hardness materials and heat-resistant alloys, and describes its MS Plus coating as giving long tool life on materials up to 52 HRC. Those are manufacturer claims, so treat them as a starting point and verify on your own parts.
The practical value for a shop is the combination of documented cutting conditions, consistent quality batch to batch and a range wide enough to cover steel, stainless, hardened steel, aluminium and difficult materials from one supplier. Fewer brands in the tool crib also means fewer variables to troubleshoot.
Five ways to lower cost-per-part this quarter
Pick your top three tools by spend. Start where the money is, not with the cheapest items.
Run a controlled trial. Same machine, same material, same program, one variable changed. Record parts per edge or per tool.
Count the whole cost. Include machine minutes, tool changes and scrap in the comparison, not just the unit price.
Review parameters with the supplier. Many shops run well below the recommended cutting conditions out of habit.
Hold sensible stock of fast movers. With supplier delays still reported across the region, a local stock position protects your delivery dates.
Practical takeaways for Malaysian machine shops
Rising freight and material costs are largely outside your control. Tool life, cycle time and scrap are not.
Judge cutting tools on cost-per-part, measured on your own jobs.
Ask for the manufacturer's recommended cutting conditions and compare them with what your machines run today.
Keep trial data. It becomes your evidence for the next purchasing discussion.
Talk to an authorised distributor
KS Precision Tools (M) Sdn Bhd is an authorised distributor in Malaysia for DIAEDGE and Mitsubishi Materials cutting tools, alongside MOLDINO, ROHM, OKABE and H.T.D Hayasaka. If you would like to run a cost-per-part trial on one of your high-volume jobs, contact our Seri Kembangan team and we will help you set it up.

Comments